Anti-Static Bag triggers Touch Points on #PineDio Stack #BL604 ... This could be our "Robot Finger" for Auto-Testing the Touch Panel 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Motor with Anti-Static Bag ... Might work for Auto-Testing the #PineDio Stack Touch Screen 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Wiring up #PineDio Stack #BL604 @PINE64 and PineCone BL602 ... To SBC for Auto Flash & Test 🤔

https://lupyuen.github.io/articles/auto

Connect these pins on #PineDio Stack #BL604 to our SBC for Auto Flash & Test: 1️⃣ GPIO 8 2️⃣ Reset 3️⃣ Ground

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604: GPIO 8 is already connected to SBC ... But GPIO 8 Jumper MUST be set to Low ... Otherwise the LoRaWAN Auto-Test goes wonky and fails 🤔

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

#PineDio Stack #BL604 and PineCone BL602 ... All boxed up with SBC for Auto Flash & Test 🙏

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604 @PINE64 ... Yep it works! 🎉 ... Up Next: Robot Finger 🤖 👉

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Here's how we Auto Upload the Test Log to GitHub Releases ... Thanks to GitHub CLI 👍

https://github.com/lupyuen/remote-bl602#upload-test-log

Automated Testing of Apache #NuttX RTOS on #PineDio Stack #BL604 @PINE64 ... All shall be explained in this article

https://lupyuen.github.io/articles/auto2?1

Apache #NuttX Testing on #PineDio Stack #BL604 is now Fully Automated ... Except for the Touch Panel which needs a Human Touch 👉

https://lupyuen.github.io/articles/auto2?2

Automated Testing on #PineDio Stack #BL604 covers GPIO, SPI, I2C, LoRaWAN and Touch Panel

https://lupyuen.github.io/articles/auto2?3#testing-checkpoints

Here's how we connect #PineDio Stack #BL604 to an SBC for Automated Testing

https://lupyuen.github.io/articles/auto2?4#connect-pinedio-stack-to-sbc

How we run the Automated Test for Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?5#run-automated-test

Our Automated Test Script flashes and boots Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?6#nuttx-must-boot

Here's how we automagically flash and boot #PineDio Stack #BL604 with an SBC

https://lupyuen.github.io/articles/auto2?7#checkpoint-alpha

Our Automated Test for #PineDio Stack #BL604 detects whether Apache #NuttX RTOS has crashed ... And runs a Crash Analysis

https://lupyuen.github.io/articles/auto2?8#nuttx-must-not-crash

Our Automated Test for #PineDio Stack #BL604 decodes the addresses in the Crash Dump ... By looking up the #RISCV Disassembly

https://lupyuen.github.io/articles/auto2?9#checkpoint-bravo

SPI Bus on #PineDio Stack #BL604 is shared by 3 SPI Devices ... Here's how we do the Automated SPI Test

https://lupyuen.github.io/articles/auto2?10#spi-test

@kreyren @lupyuen @PINE64 I wouldn't know how. The image isn't detailed enough.

@sad_electronics @lupyuen @PINE64 afaik CIA has tools to reconstruct the missing geometry, but i am not sure how usable it is.

@sad_electronics @PINE64 Me too! 🙂

@lupyuen I'm excited about the future of the little LoRa devices

@minnix Plenty more LoRa Devices on Tindie 🙂

https://www.tindie.com/search/?q=Lora

@lupyuen To my understanding does this work as ESD bags are conductive to basically "Short" the ESD. If they touch the touchscreen it changes the capacity and is thus interpreted as a input.

@sad_electronics Cool thanks! Lemme put a motor inside the ESD Bag ... See whether it can trigger touch points when needed